Please log AMC13 test activity below, blog style (new entries at top)

2012-07-08, hazen

New firmware version 0xe. Still see problem#2 below. Investigating.

2012-07-07, hazen

Trying to reproduce a DAQ firmware problem.

Test #1 - failure to reset

(set Xilinx board to deliver fast triggers at 20kHz)

cms1 (DCCdiagnose.exe) cms2 (AMC13Tool.exe) Notes
ttc/trig 1   Enable triggers
ttc/trig 4   Disable triggers
  wv 3 410 Enable AMC inputs
  wv 1 1 Set run mode
  wv 0 1 Reset all
  rv d Read word count
  0xd 0x712 FAIL: Should be zero!
  wv 0 1 Reset all
  rv d Read word count
  0xd 0 Always zero 2nd time

This fails intermittently.

Test 2 with AMC13DaqTest.exe

cms1 (DCCdiagnose.exe) cms2 (AMC13DaqTest.exe) Notes
  en 5,11 Enable AMC inputs 5, 11 and reset AMC13
ttc/cmd 1   Reset EvN to 1
ttc/l1a   Make one trigger
  rd Read and display event
  ne advance to next event
ttc/l1a   Make trigger
  rv 0x4000 10 See corrupted data

This fails consistently:

It is probably a software problem, but it seems that I am competing for use of the TTC system so stop for now.

2012-07-05, hazen

Debugged AMC13 event readout code, added file dump feature to AMC13DaqTest.cc. Discovered a firmware issue which causes data to appear incorrect after the first event, reported to Wu.

E-mailed Jeremy to ask about word order question.

2012-07-01, hazen

Install new release 11_5_0 in daqowner. Do not set as default yet. Oops, 11_5_0 is buggy. Update immediately to 11_5_1 and make it the default.

2012-06-29, hazen

Checked in to CVS several updates of work done with Charlie.

HyperDAQ

    DTCManager.cc/hh were updated to include Charlie's new HyperDAQ. This required substantial changes to the address tables. These changes were done to the existing files AMC13_AddressTable_S6/V6.txt.

Run Control

    AMC13.cc/hh were updated to add startRun(), endRun(), AMCInputEnable(), nextEventSize(), readNextEvent().

2012-06-27, rohlf

Fix AMC13Tool to support hex version names in firmware files. Fork address tables with names AMC13_AddressTable_S7/V8.txt. FIXME: This address table is now incompatible with the one used by the rest of the software!

2012-06-12, hazen

First release firmware and instructions for DAQ in AMC13:

to set up L1A:
set L1a to about 20KHz
start dccdiagnose.exe
ttc/trig 4(turn off L1A)

run amc13tool
wv 3 410 (enable amc5 and amc11)
wv 1 1 (set run bit)
wv 0 1 (reset all)

ttc/cmd 0x28(reset orbit number)
ttc/trig 1 (enable L1A)

this will take 0x800 events in the memory and throw away all when the buffer is full.

In general, the initialization  and read out remains basically the same as with DCC2.

2012-05-24, rohlf

Sucessfully updated Spartan firmware from v3 to v6 at point 5. This was accomplished remotely in Bat. 40 at CERN with AMC13Tool by first writting Spartan v6 to flash at 0x000000 (its old location) as if programming the Header, power cycling the AMC13 module with the NAT tool, reprogramming the flash Header (0x000000), Golden (0x100000), Spartan (0x200000), and Virtex (0x400000), and then issuing the software command to reconfigure from flash.

2012-05-24, rohlf

Update firmware in cDAQ lab at CERN using python software. Older software (now named amc13_python_backup-23-may2012) was used to program Spartan firmware v6 into 0x0, power cycle crate, program Header (0x000000), Golden (0x100000), Spartan (0x200000), and Virtex (0x400000) where in the process a bug was discovered in programming the header due to incorrect erase of a single page, power cycling again, and verifying the configuration.

2012-04-27, hazen

Install HCAL xDAQ 11.4.0 (as daqowner) per instructions:

To install on a teststand (as daqowner) :
      wget http://cmshcalweb01.cern.ch/hcalsw/release/installDAQ_11_4_0.perl
      perl installDAQ_11_4_0.perl --mode=teststand
      ~daqowner/common/bin/pickRelease.sh (choose 11.4.0)

You can make a code-development area on a teststand or USC using
      perl installDAQ_11_4_0.perl --mode=[teststand|usc]
--ownsource=${HOME}/src/11_4_0 --packages=hcalUpgrade --cvsuser=[your afs id]
You can list multiple packages, separated by commas.

2012-01-10, hazen

Trying to program a new AMC13 MMC. Plug in to crate, connect JTAG ICE 3 cable to JTAG connector. Fails to program. Try to force power on with "pwr_on 9" (it's in AMC slot 4) but doesn't help.

Note:

  pwr_on [fru #]
  pwr_off [fru #]

  where [fru #] is the fru number starting with 5 to16. That means if you
  want to switch on e.g. AMC2 use the command "pwr_on 6".

Remembering wisdom of Tom Gorski:

    Maybe grasping at straws here, but if you look at the reset circuit for the AVR on the MMC schematic page, you see that it is important for the IPMI_ENABLE# line to be driven low, in order to release reset. You didn't say what your power situation was to the card. If you had it in a rig with an MCH trying to talk to the card, then the IPMI_ENABLE# line would indeed be zero, and the FET would not be pulling reset low, and the problem is probably somewhere else. On the other hand, if you have the card in a rig with a dumb power supply, then AVR reset will be pulled low unless a shunt is installed at JMP4. Since reset goes to the JTAG connector you might be able to check this with a voltmeter.

This should be taken care of by the uTCA backplane, no? Meanwhile, trying to program the thing in Wu's test fixture. Doesn't work. Checking to be sure jumpers are installed. AHA ... the required ECO (soldered wire) on the T3 board was missing. Now all is OK. One can indeed program the MMC on a new board in a MicroTCA crate.

Another observation: an AMC won't power up fully without the front panel hardware installed, as the handle switch must be depressed for the negotiation with the MMC to complete.

2011-12-06, heister

cms2: SLC5 updated, installation fine tuned, PyChips and microHAL installed for the "daq" user, all tested and works

2011-12-06, hazen

Install 2nd NIC on cmssun2 (old Dell computer, Ubuntu 10.04 OS). Cable to AMC13 in uTCA crate. Install IPBus test firmware from Wu. Install PyChips. Works! (I think).

Added AMC13FlashProgramming page.

2011-12-02, hazen

Started this log. One dead NAT-MCH at Boston. 2nd NAT-MCH shipped from MN by Jeremy.

Reset I/P address to 192.168.1.11 and connect to CMS1. One can now do cms1> telnet 192.168.1.11. But, this MCH has firmware v2.0 which doesn't work with AMC13 (symptom is both red/green LEDs blink forever on AMC13 with MMC firmware V1.2).

Updating MCH firmware to V2.10 received from NAT on 9/20/11. Briefly, the procedure is:

  unzip the e-mail attachement somewhere
  copy the "bin" file to /tftpboot/mch on cms1.bu.edu
  connect to the MCH using the USB console and type "update_firmware" and follow the prompts
  type "reboot" to load the new firmware

It works! Now the AMC13 seems to be up and running with the MCH.

-- EricHazen - 02 Dec 2011

Edit | Attach | Watch | Print version | History: r163 | r16 < r15 < r14 < r13 | Backlinks | Raw View | Raw edit | More topic actions...
Topic revision: r14 - 08 Jul 2012 - EricHazen
 
  • Edit
  • Attach
This site is powered by the TWiki collaboration platform Powered by PerlCopyright © 2008-2019 by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding TWiki? Send feedback