Tags:
view all tags
---++Flash Layout *All Flash memory programming is done with the Spartan (T2). From T2 firmware version 0x6 onward, the flash memory is organized as follows:* |address| | |0x000000|header| |0x100000|Spartan "golden" backup| |0x200000|Spartan| |0x400000|Virtex| ---++Firmware Files See AMC13Firmware page for current firmware releases. NOTE: earlier versions of the spartan firmware (pre v6) use address 0x0 for the Spartan. These modules can be reloaded without a cable by writing v6 to 0x0, powercycling to configure from flash, loading the flash according to the table above, and finally powercycling to get the current configuration. ---++Flash Programming Instructions 1. Instructions on how to update your AMC13 firmware using *AMC13Python software* (recommended) are [[p_flash][here]] 2. Instructions on how to update your AMC13 firmware using the *xDAQ C++ !AMC13Tool executable* are [[AMC13ToolRecipes#UpdateFirmware][here]] 3. Instructions on how to program your AMC13 from a bit file using a *Xilinx JTAG cable* are below: * *Assumptions* * You have Xilinx "Impact" software installed on your computer. * You have a Xilinx JTAG cable with an appropriate adapter (shown [[http://ohm.bu.edu/~chill90/pics/20121005_125912.jpg][here]]) for connecting to the AMC13 front panel * *NOTE:* You generally should not have to program via JTAG unless your firmware has become corrupted and the AMC13 software can no longer talk to your module. If this is not the case and you can in fact communicate with your AMC13, please use the Python/C++ tools and follow the directions at the above links * *Instructions* 1. Download the following bit file to your computer (in a known, accessible location): [[http://physics.bu.edu/~wusx/download/AMC13/amc13T2v6.bit]] 1. Connect your JTAG cable to the bottom-most of the two 10-pin, rectangular, male sockets on the front panel of your AMC13. Note that "pin 1" is in the upper left-hand corner of the connector 1. Once your JTAG cable is connected, open the IMPACT software on the computer which is connected to the other end of your JTAG cable 1. The software will prompt you about loading past projects and creating new ones. Just say no/cancel to all of these opions. 1. Once the main window for IMPACT is up, click on the *Boundary Scan* icon in the "iMPACT Flows" sub-window. 1. Once you have done this, *right click* on the large sub-window and select *intialize chain* 1. A window will then pop up asking you to assign configuration files. Cancel out of this. 1. Make sure that at the bottom of your large sub-window, there is a blue rectangle which reads "Identify Succeeded". Also, you should now see a graphic (in this same sub-window) of both the Virtex and Spartan chips in your AMC13 1. We want to program the *Spartan* chip! Right click on the graphic of the Spartan chip and select *assign new configuration file* 1. This should open a file browser on your computer. Find and select the bit file that you downloaded at the start of this process. 1. Once you have done this, click *program* and select *ok* 1. The bit file is loaded very quickly, so don't be alarmed if it seems like nothing happened. 1. Your Spartan chip should now be at firmware version 0x6. *Do not cycle the power at this point*. 1. Use either *AMC13Tool.exe* in the C++ software or *p_flash.py* in the Python software to update the flash for your Spartan and Virtex chips. You should program all 4 flash images (=AMC13T2Header=, =AMC13T2Golden=, =AMC13T2Vxxxxx.mcs= and =AMC13T2Vxxxxx.mcs=). After this last step is complete you should cycle the power and check that your versions are now the latest ones. -- Main.JimRohlf - 26 May 2012
Edit
|
Attach
|
Watch
|
P
rint version
|
H
istory
:
r25
|
r10
<
r9
<
r8
<
r7
|
B
acklinks
|
V
iew topic
|
Raw edit
|
More topic actions...
Topic revision: r8 - 07 Oct 2012
-
EricHazen
Home
Site map
BUCMSPublic web
Main web
Sandbox web
TWiki web
BUCMSPublic Web
Create New Topic
Index
Search
Changes
Notifications
RSS Feed
Statistics
Preferences
P
View
Raw View
Print version
Find backlinks
History
More topic actions
Edit
Raw edit
Attach file or image
Edit topic preference settings
Set new parent
More topic actions
Account
Log In
Register User
Edit
Attach
Copyright © 2008-2022 by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding TWiki?
Send feedback