10 Prototype boards with red front panels were manufactured in early 2009. These boards are not identical to the production boards because they have a smaller FPGA. The production front panels are marked "DCC2" and are black.

Boards are numbered in decimal starting with 2001 for the first prototype up to a maximum possible number of 2255. The first digit is always '2'. The other three digits represent the decimal equivalent of the binary value set by cutting jumpers on the PCB.

You can find out which board is where in the pit as follows:

(log on to a head node, i.e. cmsusr1 etc)

$ cd ~ehazen/GetStatus
$ ./getAllVersions.sh | ./parseVersions.pl

 Crate  Bus    Slot   Xilinx     LRB        VME    S/N  FED
 ====================================
     4  caen:0 10     0x3018     0x010a     0x0104 2001 700
     4  caen:0 20     0x3018     0x010a     0x0104 2002 701
     0  caen:1 10     0x3018     0x010a     0x0104 2174 702
     0  caen:1 20     0x3018     0x010a     0x0104 2176 703
       .... remainder of list truncated ...

Here is Dick Kellogg's list which may become the official one. For now, you have to check both.

Prototype Boards

S/N	Location	Notes
2001	904	Tested in MWGR 15
2002	904
2003	904
2004	904
2005	BU - Test stand
2006	Whitman	To be destructively tested for soldering temperature profiles
2007	BU	Ethernet resistor replaced - re-test
2008	BU	Ethernet resistor replaced - re-test
2009	BU	Tested. No errors
2010	BU

Production Boards

The production board serial numbers start with 2129 as shown below. On the PCB, the binary "jumpers" (actually cut traces) start with "10000001".

Note that you can sort the table below by clicking the column headings. Sort by Location for an easy way to check how many boards are where.

S/N	Location	Notes	Date shipped	Status
2145	904 Spares	"Stops sending events down SLINK and goes to OFW at 80 kHz" . Tested OK by PDL 4/1/11	11/16	OK
2176	FED_727	31 July 2011: Removed from FED 703 due to BcN mismatch problems. This occurred during ramping and is likely not an actual DCC issue: http://cmsonline.cern.ch/cms-elog/631675 3 Aug 2011: Installed as FED 727 http://cmsonline.cern.ch/cms-elog/637389	3 Aug 2011	OK
2187	BU	Board is warped. won't fit into crate.		Sick
2152	904 Hospital	CRC Errors in Event Builder but not LRB. All errors from single LRB chip. See details below	6/11/2010	Sick
2181	904 Hospital	CRC erros and "miscellaneous errors" during intervention on a different DCC problem: http://cmsonline.cern.ch/cms-elog/637389	3 Aug 2011	Sick
2172	904 Hospital	CRC errros on LRB FPGA serving spigots 12,13,14. Elog: http://cmsonline.cern.ch/cms-elog/605813 Replaced LRB4 @ CERN shop. All FW in FLASH except VME FW corrupted. Now fails memory test on LRB2? Elog: http://cmsonline.cern.ch/cms-elog/689158	5 Oct 2011	Sick
2163	BU	DDR memory chip replaced	2 Aug 2011	OK
2154	FED_704	Installed on 12 Jul 2011	12 Jul 2011	OK
2139	FED_716	Installed on 3 Aug 2011 http://cmsonline.cern.ch/cms-elog/637389	3 Aug 2011	OK
2155	FED_729	Installed on 3 Aug 2011 http://cmsonline.cern.ch/cms-elog/637389	3 Aug 2011	OK
2198	BU	Not ever tested?		?
2130	*904 Hospital	Orbit number mismatches as FED 731 01-jul-2009 (removed)	5/26	Sick
2142	FED_701	Prior incident as different FED (3/24/10): Was removed when we had an issue where no HTRs were sending data. No other symptoms point to DCC failure	6/11/10	OK
2158	BU	Problem: DSP FW version 0x301c reports as version 0x0 on this board. Can program manually with DCC2Tool.exe w/o issues. CRC of DSP FW reported by DCC2Tool.exe is correct.	6/1 (returned)	Sick
2133	904 Hospital	Removed due to CRC errors during intervention on other DCC issues. Suspect spurious issue: http://cmsonline.cern.ch/cms-elog/637389	3 Aug 2011	OK
2160	904 Hospital	Removed from FED 700 due to UERR on spigot 13 - 10/29/09.	6/1	Sick
2134	BU	Returned to BU because of alleged mis-matches	5/26	Sick
2193	BU	Returned ~3/10/10 w/ spigot 3 problem (CASTOR)	1/10	Sick
2136	BU	Shipped back to BU 6/9/09 per dick	to CERN 5/26	OK
2129	FED_730	Tested.	5/26	OK
2131	FED_720	Tested.	5/26	OK
2132	FED_718	Tested.	5/26	OK
2138	FED_726	Tested.	5/26	OK
2141	FED_723	Tested.	5/26	OK
2144	FED_722	Tested.	5/26	OK
2148	FED_721	Tested.	5/26	OK
2150	FED_719	Tested.	7/1	OK
2151	FED_712	Tested.	6/1 OK
2153	FED_710	Tested.	6/1	OK
2156	FED_714	Tested.	6/1	OK
2161	FED_708	Tested.	6/1	OK
2162	FED_716	Tested.	6/1	OK
2164	FED_715	Tested.	6/9	OK
2165	FED_711	Tested.	6/9	OK
2166	FED_731	Tested.	6/9	OK
2168	FED_707	Tested.	6/9	OK
2169	FED_706	Tested.	6/9	OK
2171	FED_717	Tested.	6/9	OK
2173	FED_705	Tested.	6/9	OK
2174	FED_702	Tested.	6/9	OK
2177	FED_709	Tested.	7/1	OK
2179	FNAL	Tested.	Ship to FNAL 2011-05-12	OK
2182	*CERN	Tested.	7/1	OK
2183	BU	Tested.	Ship to MN 2011-05-12	OK
2190	CERN	Tested.	1/10	OK
2191	CERN	Tested.	1/10	OK
2192	CERN	Tested.	1/10	OK
2194	BU	Tested.	3/11/11 -- problems with spigots 3-5 (Eric/Dick)	Sick
2197	BU	Tested.		OK
2159	FED_713	Tested. 8/18/11 fail LRB4 test, however, this LRB is not in use (no spigots attached to HTRs)	6/1	LRB4 sick
2185	CERN	Tested. Shipped to CERN	8/18/11	OK
2149	BU	Tested. U0 soldering problem(most likely because U10 looks OK) Multiple lines to U10 without connection		Sick
2175	CERN	Tested. Broken LED-->VME. Declared good, shipped to CERN	8/18/11	OK
2184	BU	Tested. CRC error, SLINK error. "event size of 4800 words is unreasonable"		Sick
2170	BU	Tested. CRC errors. Spigot zero bad?		Sick
2143	CERN	Tested. Ethernet error(RJ 45). Was not fixed. Returned to BU 6/9/09. Tested/shipped back to CERN	8/18/11	OK
2188	BU	Tested. Ethernet RJ45 error.		Sick
2135	FED_724	Tested. HTR13 LED broken. Now fixed.	5/26	OK
2137	FED_725	Tested. Initially 2 errors. 2nd time tested-no errors. Probably a wiring issue.	5/26	OK
2140	FED_728	Tested. Initially 2 errors. 2nd time tested-no errors. Probably a wiring issue.	5/26	OK
2178	FED_700	Tested. Installed to replace 2160 - 10/29/09	7/1	OK
2146	BU	Tested. Pin9 of HTR14 RJ45 to U14 line open. Could be a PCB problem.		Sick
2186	CERN	Tested. Shipped to CERN	8/18/11	OK
2189	CERN	Tested. Shipped to CERN	8/18/11	OK
2195	CERN	Tested. Shipped to CERN	8/18/11	OK
2196	CERN	Tested. Shipped to CERN	8/18/11	OK
2167	BU	Tested. Spigot CRC error/SLINK error		Sick
2180	BU	Tested. TTS link error. SLINK error.		Sick
2147	BU	Tested. Two broken LEDs, Ethernet error(RJ 45), and CRC error. R25 cold solder,D25 is also missing. Errors fixed as of 6/3		OK
2157	*CERN	Tested. Warped board	6/1	OK/warped

Changes:

S/N 2159 fails LRB4 link/memory test in the pit as FED 713. PDL discovered that these spigots are not in use on this FED and opted not to swap out.

-- EricHazen - 18 Aug 2011

S/N2163 LRB0 memory chip replaced. OK now. -- Main.Shouxiang Wu - 2 Aug 2011

S/N 2172 showed CRC errors on LRB FPGA serving spigots 12,13,14. Replaced in USC on 12 Jul 2011. Installed in 904 and powered up to find all LRB chips reporting appropriate FW versions.

-- PhilLawson - 19 Jul 2011

Ship 2179 and 2183 to FNAL and MN, respectively. Track# 1Z0159190193593478 and 1Z0159190190690681

-- EricHazen - 12 May 2011

Phil tested SN 2145 at CERN as follows:

Installed HCAL DAQ version 10.4.6 (unrelated, needed for different test)
Altered FedkitTest_LTClistenToTTS_from_slot20 to take SLINK data from slot 20.
Blasted high rate events at DCC. Due to SLINK readout (with only CRC error checking), 
  effective rate was limited to 34 kHz since this DCC was providing TTS signal.
Readout 10E6 events at this rate with no SLINK errors. Good enough for me.

-- PhilLawson - 24 Jan 2012

• Replaced line for 2151. This was accidentally removed during an edit a long while back. Good thing for twiki history!

-- EricHazen - 01 Apr 2011

• SN 2163 showed CRC errors on LRB chip serving spigots 0,1,2
  • SN 2177 installed in place as FED 709
  • Details in eLog: http://cmsonline.cern.ch/portal/page/portal/CMS%20online%20system/Elog?_piref815_429145_815_429142_429142.strutsAction=%2FviewMessageDetails.do%3FcatId%3D3%26subId%3D9%26msgId%3D468995

-- PhilLawson - 26 Jan 2011

• Updated list to reflect install of SN 2141 as FED 701 to replace sick DCC SN 2152.
  • SN 2152 evidenced communication problems between LRB and Event Builder chip
  • Details in eLog: 402680 on June 7 2010

-- PhilLawson - 11 Jun 2010

• Updated list to reflect swap of SN 2142 as FED 727

-- PhilLawson - 13 Apr 2010

• Updated list per inventory from Dick. Location with * were confirmed at CERN per Dick's 12/14/09 inventory.

-- EricHazen - 14 Dec 2009

• Check and update a few mistakes in the list of installed DCC2

-- EricHazen - 11 Dec 2009

• FED 719 (S/N 2145) was consistently going to OFW at 80 kHz. No events being sent down SLINK. Replaced DCC with S/N 2150

-- PhilLawson - 16 Nov 2009

• Logged in today and found FED 700 is now S/N 2160 (was previously 2001), FED 701 is now S/N 2152 (was previously 2002)
• Problem with FED 710 & DSP FW 0x301c described above.

-- PhilLawson - 26 Aug 2009