AMC13 MMC Software

The AMC13 MMC software package can be found in the amc13config directory in the xDAQ release or Standalone Release. This package is a collection of python scripts which provide the ability to store configuration information into non-volatile EEPROM memory for each SPI port, to apply directly configuration information to an AMC13 after power up, and to issue useful commands remotely such as resets and handle swaps.

NOTE!! Some of these scripts are use PERL scripts found in the config_tools directory

Contents
systemVars.py
readIPs.py
readNVmem.py
applyConfig.py
storeConfig.py
backendPower.py
coldReset.py
handleOverride.py

systemVars.py

This Python module holds some important variables which, once set, probably won't need to be changed again (on a given system). This file conveniently makes it so that once properly adjusted, all default values for amc13Config script flags should be useful.

Variable	Description
DEFAULT_HOST_IP	The IP address for your commercial MCH module in the uTCA crate
DEFAULT_AMC13_SLOT	The desired default slot value for your AMC13 (on-based, as listed on the front of the Vadatech uTCA crate)
DEFAULT_CONFIG_DIR	The location of the PERL tools which are used for the MMC actions (this shouldn't ever need to be changed)
NETWORK_BASE	The network base for all IP addresses in your uTCA crate

readIPs.py

This Python script is used to read out the IP address for each Tongue on the AMC13 using IPMI:

./readIPs.py (--host=<ip_addr>) (--slot=<n>)

All flags that are in parentheses are optional and and will take on their default values as listed in systemVars.py if not explicitly specified.

Flag	Description
--host	Host IP address for your uTCA crate. This should be the IP address of your commercial MCH1 module. If not specified, defaults to value in systemVars.py
--slot	Slot number (as seen on the uTCA crate, ie one-based) of AMC13 to be configured. If not specified, defaults to value in systemVars.py

readNVmem.py

This Python script is used to read out 40 bytes of non-volatile memory at an address specified by an NV area read

./readNVmem.py (--host=<ip_addr>) (--slot=<n>)

Flag	Description
--host	Host IP address for your uTCA crate. This should be the IP address of your commercial MCH1 module. If not specified, defaults to value in systemVars.py
--slot	Slot number (as seen on the uTCA crate, ie one-based) of AMC13 to be configured. If not specified, defaults to value in systemVars.py

applyConfig.py

This Python script is used to apply (not store) IP address to each Tongue on the AMC13 after powerup:

./applyIPs.py (--host=<ip_addr>) (--slot=<n>) --spartan=<ip_addr> --virtex=<ip_addr>

Optionally, you can specify only one IP address instead of both, which will apply the provided IP to T2 while applying an IP whose final byte is one higher than the provided IP to T1. For example, the flag command would set the following IP addresses:

--ip=192.168.1.100
  Spartan: 192.168.1.100
  Virtex: 192.168.1.101

As yet another option, you can simply specify the serial number of your AMC13, which will apply IP addresses to both Tongues via the following scheme:

--serial=<SN>  
  Spartan: 192.168.1.(254-(2*SN))
  Virtex: 192.168.1.(255-(2*SN))

All flags in parentheses are optional and will take on their values as listed in systemVars.py if not explicitly specified.

Flag	Description
--host	Host IP address for your uTCA crate. This should be the IP address of your commercial MCH1 module. If not specified, defaults to value in systemVars.py
--slot	Slot number (as seen on the uTCA crate, ie one-based) of AMC13 to be configured. If not specified, defaults to value in systemVars.py
--spartan	IP address to be assigned to T2
--virtex	IP address to be assigned to T1
--ip	IP address to be assigned to T2 with an IP address with the final byte one larger than the provided IP to be assigned to T1. This flag can only be used instead of (not in addition to) the --spartan and --virtex flags
--serial	Assign the IP addresses of both Tongues using the provided serial number: T2 ~ 192.168.1.(254-(2*SN)), T1 ~ 192.168.1.(255-(2*SN))

storeConfig.py

This Python script is used to store (not apply) IP addresses in the MMC EEPROM for the configuration of both Tongues upon powerup:

./storeConfig.py (--host=<ip_addr>) (--slot=<n>) --spartan=<ip_addr> --virtex=<ip_addr>

Optionally, you can specify only one IP address instead of both, which will store the provided IP for T2 while storing an IP whose final byte is one higher than the provided IP for T1. For example, the flag command would store the following IP addresses:

--ip=192.168.1.100
  Spartan: 192.168.1.100
  Virtex: 192.168.1.101

As yet another option, you can simply specify the serial number of your AMC13, which will store IP addresses for both Tongues via the following scheme:

--serial=<SN>  
  Spartan: 192.168.1.(254-(2*SN))
  Virtex: 192.168.1.(255-(2*SN))

All flags in parentheses are optional and will take on their values as listed in systemVars.py if not explicitly specified.

Flag	Description
--host	Host IP address for your uTCA crate. This should be the IP address of your commercial MCH1 module. If not specified, defaults to value in systemVars.py
--slot	Slot number (as seen on the uTCA crate, ie one-based) of AMC13 to be configured. If not specified, defaults to value in systemVars.py
--spartan	IP address to be assigned to T2
--virtex	IP address to be assigned to T1
--ip	IP address to be assigned to T2 with an IP address with the final byte one larger than the provided IP to be assigned to T1. This flag can only be used instead of (not in addition to) the --spartan and --virtex flags
--serial	Assign the IP addresses of both Tongues using the provided serial number: T2 ~ 192.168.1.(254-(2*SN)), T1 ~ 192.168.1.(255-(2*SN))

backendPower.py

This script is used to enable and disable the back-end power remotely to the AMC13. The script is to be run as follows:

./backend_power (--host=<ip_addr>) (--slot=<n>) --enable|--disable

All flags in parentheses are optional and will take on their values as listed in systemVars.py if not explicitly specified.

Flag	Description
--host	Host IP address for your uTCA crate. This should be the IP address of your commercial MCH1 module. If not specified, defaults to value in systemVars.py
--slot	Slot number (as seen on the uTCA crate, ie one-based) of AMC13 to be configured. If not specified, defaults to value in systemVars.py
--enable	Turn on the backend power
-disable	Turn off the backend power

coldReset.py

This script is used to issue a cold reset remotely to an AMC13. The script is to be run as follows:

./cold_reset (--host=<ip_addr>) (--slot=<n>)

All flags in parentheses are optional and will take on their values as listed in systemVars.py if not explicitly specified.

Flag	Description
--host	Host IP address for your uTCA crate. This should be the IP address of your commercial MCH1 module. If not specified, defaults to value in systemVars.py
--slot	Slot number (as seen on the uTCA crate, ie one-based) of AMC13 to be configured. If not specified, defaults to value in systemVars.py

handleOverride.py

This script is used to issue a handle swap remotely to the AMC13. The script is to be run as follows:

./handle_override (--host=<ip_addr>) (--slot=<n>) --in|--out|--release|--cycle

All flags in parentheses are optional and will take on their values as listed in systemVars.py if not explicitly specified.

Flag	Description
in	Force handle in
out	Force handle out
cycle	Force handle out for 10 seconds and then issue a release
release	Handle not forced, but instead the actual handle position is payed attention to
--host	Host IP address for your uTCA crate. This should be the IP address of your commercial MCH1 module. If not specified, defaults to value in systemVars.py
--slot	Slot number (as seen on the uTCA crate, ie one-based) of AMC13 to be configured. If not specified, defaults to value in systemVars.py

-- CharlieHill - 08 May 2013