Line: 1 to 1 | ||||||||
---|---|---|---|---|---|---|---|---|
uHTRTool software procedures which are useful to an AMC13 debugger and developer.
| ||||||||
Added: | ||||||||
> > |
| |||||||
| ||||||||
Line: 134 to 135 | ||||||||
New presamples : [0] 4 [...] Selection : [-1] 5 | ||||||||
Changed: | ||||||||
< < | New pipeline length : [0] 50 | |||||||
> > | New pipeline length : [0] 8 | |||||||
[...] | ||||||||
Added: | ||||||||
> > | Selection : [-1] 15 TP presamples : [2] 2 Selection : [-1] 16 TP samples : [2] 2 | |||||||
Selection : [-1] 7 [...] Selection : [-1] 8 | ||||||||
Line: 159 to 164 | ||||||||
Module Id : 0 (0x0) BC Offset : 0 | ||||||||
Added: | ||||||||
> > | Old DAQ enabled menu options:
Selection : [-1] 3 New nsamples : [0] 10 [...] Selection : [-1] 4 New presamples : [0] 4 [...] Selection : [-1] 5 New pipeline length : [0] 50 [...] Selection : [-1] 7 [...] Selection : [-1] 8
| |||||||
Setup ClockWhen checking the status of you uHTR, a list of the clocks are reported (for both front and back). These reported clocks should be consistent with the expected clock (see below). Inconsistencies may indicate that you will need to setup clocks. |
Line: 1 to 1 | ||||||||
---|---|---|---|---|---|---|---|---|
uHTRTool software procedures which are useful to an AMC13 debugger and developer. | ||||||||
Line: 112 to 112 | ||||||||
TP ZS : TP_NZS Module Id : 0 (0x0) BC Offset : 0 | ||||||||
Added: | ||||||||
> > |
| |||||||
|
Line: 1 to 1 | ||||||||
---|---|---|---|---|---|---|---|---|
uHTRTool software procedures which are useful to an AMC13 debugger and developer. | ||||||||
Line: 160 to 160 | ||||||||
Send uHTR Local Triggers | ||||||||
Changed: | ||||||||
< < | The following procedure assumes that the backplane link sees Bc0s running both ways between the uHTR and the AMC13. It's also worth saying that the following procedure is from Jeremy, and that upon it's initial test, it did not work. We are not sure what the problem is yet, but this list of command may need to be modified. (EDIT: recipe below seems to be working) | |||||||
> > | The following procedure assumes that the backplane link sees Bc0s running both ways between the uHTR and the AMC13. It's also worth saying that the following procedure is from Jeremy, and that upon it's initial test, it did not work. We are not sure what the problem is yet, but this list of command may need to be modified. | |||||||
LINK FE_RAMS |
Line: 1 to 1 | ||||||||
---|---|---|---|---|---|---|---|---|
uHTRTool software procedures which are useful to an AMC13 debugger and developer. | ||||||||
Line: 160 to 160 | ||||||||
Send uHTR Local Triggers | ||||||||
Changed: | ||||||||
< < | The following procedure assumes that the backplane link sees Bc0s running both ways between the uHTR and the AMC13. It's also worth saying that the following procedure is from Jeremy, and that upon it's initial test, it did not work. We are not sure what the problem is yet, but this list of command may need to be modified. | |||||||
> > | The following procedure assumes that the backplane link sees Bc0s running both ways between the uHTR and the AMC13. It's also worth saying that the following procedure is from Jeremy, and that upon it's initial test, it did not work. We are not sure what the problem is yet, but this list of command may need to be modified. (EDIT: recipe below seems to be working) | |||||||
LINK FE_RAMS |
Line: 1 to 1 | ||||||||
---|---|---|---|---|---|---|---|---|
Added: | ||||||||
> > |
uHTRTool software procedures which are useful to an AMC13 debugger and developer.
Program uHTR FlashThe uHTR consists of two FPGAs, a 'front' and a 'back'. You can find the firmware files for each chip here
Enable uHTR DAQ Path
Send uHTR Local TriggersThe following procedure assumes that the backplane link sees Bc0s running both ways between the uHTR and the AMC13. It's also worth saying that the following procedure is from Jeremy, and that upon it's initial test, it did not work. We are not sure what the problem is yet, but this list of command may need to be modified.LINK FE_RAMS SETUP Enable? = 1 TTC aligned? = 1 Delay between TTC oribt and pattern start = 0 ISOPULSE Fiber = 6 Chan = 2 Amplitude = 20 Bunch = 300 TRIG LUTS Set 1-1 LUT Which group of LUTs? = 0 Choose index = -1 Set 1-1 LUT Which group of LUTs? = 1 Choose index = -1 TRIG SELF Set thresholds Which threshold = -1 Set to what value? = 5-- CharlieHill - 31 May 2013 |