Line: 1 to 1 | ||||||||
---|---|---|---|---|---|---|---|---|
| ||||||||
Line: 8 to 8 | ||||||||
Specification and User Guide | ||||||||
Changed: | ||||||||
< < |
| |||||||
> > |
| |||||||
|
Line: 1 to 1 | ||||||||
---|---|---|---|---|---|---|---|---|
| ||||||||
Line: 11 to 11 | ||||||||
| ||||||||
Added: | ||||||||
> > |
| |||||||
Serial Numbers |
Line: 1 to 1 | ||||||||
---|---|---|---|---|---|---|---|---|
| ||||||||
Line: 9 to 9 | ||||||||
Specification and User Guide
| ||||||||
Changed: | ||||||||
< < | ||||||||
> > |
| |||||||
Serial Numbers |
Line: 1 to 1 | ||||||||
---|---|---|---|---|---|---|---|---|
| ||||||||
Line: 8 to 8 | ||||||||
Specification and User Guide | ||||||||
Changed: | ||||||||
< < |
| |||||||
> > |
| |||||||
|
Line: 1 to 1 | ||||||||
---|---|---|---|---|---|---|---|---|
| ||||||||
Line: 10 to 10 | ||||||||
| ||||||||
Added: | ||||||||
> > |
| |||||||
Serial Numbers |
Line: 1 to 1 | ||||||||
---|---|---|---|---|---|---|---|---|
| ||||||||
Line: 9 to 9 | ||||||||
Specification and User Guide
| ||||||||
Added: | ||||||||
> > | ||||||||
Serial Numbers | ||||||||
Line: 34 to 35 | ||||||||
serial numbers 2001...200a. Note that though the serial number is read in hex, the convention is to write the number as decimal i.e. "2010" instead of "200a". | ||||||||
Deleted: | ||||||||
< < | -- EricHazen - 13 Apr 2009 | |||||||
\ No newline at end of file | ||||||||
Added: | ||||||||
> > | -- EricHazen - 03 Jan 2010 | |||||||
\ No newline at end of file |
Line: 1 to 1 | ||||||||
---|---|---|---|---|---|---|---|---|
| ||||||||
Line: 6 to 6 | ||||||||
| ||||||||
Added: | ||||||||
> > | Specification and User Guide
| |||||||
Serial NumbersEach DCC has a unique serial number, which is set by cutting a set of traces on the PCB. These are located near |
Line: 1 to 1 | ||||||||
---|---|---|---|---|---|---|---|---|
| ||||||||
Line: 11 to 11 | ||||||||
Each DCC has a unique serial number, which is set by cutting a set of traces on the PCB. These are located near the back of the board and marked "SN0" thru "SN7". SN0 is the lsb, and a cut jumper corresponds to a '1'. | ||||||||
Changed: | ||||||||
< < | To readout the serial number, start DCC2Tool.exe and enter the command vme/r 0x10 . This will display | |||||||
> > | To readout the serial number, start DCC2Tool.exe as follows:
DCC2Tool.exe caen:0 19...where the bus:crate and VME slot are as needed. Enter the command vme/r 0x10 . This will display | |||||||
an 8 digit hex value, where the first 4 digits are the serial number in hex. i.e.:
| ||||||||
Line: 20 to 27 | ||||||||
This corresponds to S/N 2005. All boards should be marked with their serial numbers. Prototype boards have | ||||||||
Changed: | ||||||||
< < | serial numbers 2001...200a. | |||||||
> > | serial numbers 2001...200a. Note that though the serial number is read in hex, the convention is to write the number as decimal i.e. "2010" instead of "200a". | |||||||
-- EricHazen - 13 Apr 2009 \ No newline at end of file |
Line: 1 to 1 | ||||||||
---|---|---|---|---|---|---|---|---|
| ||||||||
Line: 6 to 6 | ||||||||
| ||||||||
Added: | ||||||||
> > | Serial NumbersEach DCC has a unique serial number, which is set by cutting a set of traces on the PCB. These are located near the back of the board and marked "SN0" thru "SN7". SN0 is the lsb, and a cut jumper corresponds to a '1'. To readout the serial number, start DCC2Tool.exe and enter the commandvme/r 0x10 . This will display
an 8 digit hex value, where the first 4 digits are the serial number in hex. i.e.:
> vme/r 0x10 > Read 0x20050000 from offset 0x000010This corresponds to S/N 2005. All boards should be marked with their serial numbers. Prototype boards have serial numbers 2001...200a. | |||||||
-- EricHazen - 13 Apr 2009 \ No newline at end of file |
Line: 1 to 1 | ||||||||
---|---|---|---|---|---|---|---|---|
Added: | ||||||||
> > |
|